weapon lxxxi's jeep 12
- weapon lxxxi
- Posts: 456
- Joined: October 4th, 2011, 12:29 pm
- Location: South coast UK
- Contact:
Re: weapon lxxxi's jeep 12
Ah thanks yeah I remember reading now that they go opposite ways if we mount them like that. A guide on how to wire them in would be great as I have no clue on how to even start. I like this one switch relay idea too... Handy for turning on high beams down country roads. So feel free to share ha haa.
- fantomas
- Completed JP Jeep
- Posts: 551
- Joined: December 14th, 2011, 1:46 am
- Location: Connecticut
- Contact:
Re: weapon lxxxi's jeep 12
I've been waiting for the weather to warm up a little bit more so I can spray a few more coats of red plastidip on the rings. Hopefully I can get that done and finish the lights and get them installed within the next 2 weeks, but no promises (I've also been in the middle of refurbishing a ramsey winch). It's really hard to convince myself to open up all these lights to drill the holes for the mounting hardware...
- weapon lxxxi
- Posts: 456
- Joined: October 4th, 2011, 12:29 pm
- Location: South coast UK
- Contact:
Re: weapon lxxxi's jeep 12
Ha no rush, I'll have to get a relay & wire to run from the batt anyway. Yeah I saw your winch good luck ha! See I thought about drilling holes & not keen on it.... So I was going to use strong glue & to make it look like they are screwed on, just have the heads of the screw stuck on for effect? This would also fix my height problem if I get bashed going in a low parking lot. It's a tight fit in some in my area. Anyway I still have to make my guards not having joy with 3D printers over here!
But I have just ordered my new green carpet & door tops for my half doors wooo!!!
But I have just ordered my new green carpet & door tops for my half doors wooo!!!
- weapon lxxxi
- Posts: 456
- Joined: October 4th, 2011, 12:29 pm
- Location: South coast UK
- Contact:
Re: weapon lxxxi's jeep 12
Me & the jeep have Just been invited to attend this.... Woah!!!
http://bournemouthwheels.co.uk
http://bournemouthwheels.co.uk
Re: weapon lxxxi's jeep 12
Wow I have not checked this thread out in a while and that Jeep is looking amazing! I'm from the UK and I would love to see it! From Manchester so a bit of a trek!
- weapon lxxxi
- Posts: 456
- Joined: October 4th, 2011, 12:29 pm
- Location: South coast UK
- Contact:
Re: weapon lxxxi's jeep 12
Hi rougeant, thanks... Yeah it's taken a while... Very very close to finishing the little bits now.
I'll be posting some up dates in a mo as now have half doors fitted too.
It is a bit of a trek yeah but if you are ever down near by give us a shout we can meet up
I'll be posting some up dates in a mo as now have half doors fitted too.
It is a bit of a trek yeah but if you are ever down near by give us a shout we can meet up
- weapon lxxxi
- Posts: 456
- Joined: October 4th, 2011, 12:29 pm
- Location: South coast UK
- Contact:
Re: weapon lxxxi's jeep 12
Ok so I have now had my half doors finished (yup need todo the top hinge)
Here are some pics of her at the event from last weekend. Carpet to be fitted next & hopefully the winch & lights to be hooked up too
Here are some pics of her at the event from last weekend. Carpet to be fitted next & hopefully the winch & lights to be hooked up too
Re: weapon lxxxi's jeep 12
I love the Dilo in the car. That's a great touch. Looks great
- weapon lxxxi
- Posts: 456
- Joined: October 4th, 2011, 12:29 pm
- Location: South coast UK
- Contact:
Re: weapon lxxxi's jeep 12
Thanks, he was quite popular. He's not finished yet but what I have planned will be funGuyHaley wrote:I love the Dilo in the car. That's a great touch. Looks great
Re: weapon lxxxi's jeep 12
Nice Registration plate, how much did that set you back?
Who is online
Users browsing this forum: No registered users and 82 guests